Blog

How To Rewire A Floor Lamp? Easy Guide For Rewiring

A floor lamp adds charm as well as light in your room and also in the office. When you buy an expensive floor lamp or an antique floor lamp to decorate your room, but it does not work correctly with the damaged wire. Then what would you do?

Don’t worry, and you can make an old floor lamp new again with some inexpensive supplies or the right connection.

In this article, you can read some simple steps that are how to rewire a floor lamp?

How to rewire a floor lamp? 4 easy steps

Step1:

In the first step, you should ensure the wire setup and socket structure are necessary if there are two lights or one and where the wire runs for them.

This information helps full for you when you want to your floor lamp rewire.

The wire length is also sufficient for the rewiring process. Always make sure that you have an extra wire length for the plug end.

Step2:

In the second step, you should unplug the current lamp cord from the power outlet. Open the nut that is top on the lamp harp and pull out the lampshade. Choose a brand new replacement wire setup for your lamp, which includes a fresh compartment and alternation.

Some time in an antique floor lamp, it is challenging to know where the electric problem might be, therefore it is better to use only the ‘’skeleton” of the lamp for visual purposes, but to change all electrical items.

Step3:

Take the floor lamp apart. Rewire your lamp fortify the new wire to the socket with the lamp, then connect the new socket to the small wire with nuts, making sure you match the wire colors. Red wire indicates the hot and black wire is usually used for the neutral. You should ensure this thing that no bare wire is visible when making contact.

Step4:

Check it out. You should use the ground plug to check your lamp. Because this will limit the risk if you connect the wrong wire.

If your floor lamp still does not work then have look at your wire connection may be some problems with your wire.

 

Now you have a question in your mind; which rewiring kit is best for the floor lamp?

Floor lamp rewiring kit

GE 50960 repair lamp kit, yellow

Floor lamp rewiring kit

You can repair or rewire your table lamps and floor lamps with the help of the GE 3-Way lamp and floor lamp Kits.

Because this floor lamp wiring kit has a 3-way turn knob, 10 in. harp, 18-gauge cord set, finial, and fittings.

An 8 ft. clear cord is included, which can help the cord blend in with its surroundings and minimize the distraction it can cause.

The 3-way turn knob has low-medium-high settings which can allow you to regulate the quantity of sunshine within the room.

Controlling the quantity of sunshine getting used will prevent money and energy!

Note: have a professional electrician perform the installation if you’re not conversant in household wiring. This item has a 90 days warranty and is also UL listed.

How to fix a floor lamp pole?

How to fix a floor lamp pole?

If you want to light up your office or house then floor lamps are the best addition. You can also get some benefits to set a floor lamp in your home or also office.

As you know, a floor lamp is a type of lamp that stands on its own. Floor lamps stand tall to provide better lighting.

But sometimes many floor lamp poles are bend over time because the grip of the pole stays on one side and decreases on the other.

I know you have a question: how to fix a floor lamp pole?

Don’t worry we are here to solve your problems. In this topic, you can learn how to fix a damaged floor lamp pole? Let’ start.

Step1:

As safety protection, always unplug before the conduct or repairing the floor lamp. If the floor lamp has been freshly used, wait until it reaches room temperature before attempting to repair the bulb

Step2:

Check the floor lamp to find the loose part. Do this by gently touching and rotating the different parts of the lamp. A great place to start is under the lamp socket and work your way up slowly.

Step3:

Using the bottom as a spot to stabilize the lamp, take hold of the pole and wiggle it gently to work out whether the bottom is that the source of the wobbliness or if other parts of the bottom move quite they ought to.

Step4:

While holding rock bottom steady, twist the highest part of the lamp pole in a clockwise direction. This may help tighten the loose middle tube. Repeat an equivalent tread on other tubes that are attached to the lamp when necessary.

Step5:

If the matter has not yet been resolved and your lamp remains wobbly, it’s time to see the lamp base. Examine the bottom to ascertain if there are any loose screws or nuts which will be liable for the lamp’s wobbliness. If there are loose screws, simply tighten them employing a Philips-head screwdriver and set the lamp upright.

Step6:

Do the gentle wiggle test again to ascertain if all parts are properly tightened, especially the poles. If you notice that it produces an equivalent sound or the poles are still leaning or sagging, tighten it further without being too rough on the poles.

Step7:

Once you’ve got skilled the inspection again and you’ve got determined that everything from the bottom up the length of the pole is in fine condition, change the lampshade if you replace it and fix the floor lamp back in standing position.

How to rewire a bridge arm floor lamp?

How to rewire a bridge arm floor lamp?

Bridge lamps are the type of lamps that have a swinging arm that begins of the lamp base. They’re great for reading, working, or studying in spaces because they will be turned towards or far away from someone without having to maneuver the whole lamp around. They also are available in different styles and colors, and maybe won’t both decorate and illuminate work areas.

Like all lamps, bridge arm floor lamps affect over time. But that does not mean a beloved lamp has got to be tossed out directly. Given the proper steps, the worn but loved lamps are often fixed and given an entirely new life.

Before Wiring

First, you should turn the lamp and then remove the shade. Then, you’ll detach the bulb socket, which is where the sunshine bulb is screwed into the lamp.

It’s held to the lamp with a nut at the bottom. Turn the nut counterclockwise with a wrench or your fingers.

Once the nut is begun, the bulb won’t be attached. The sole thing holding it there are the wires inside the lamp.

Removing Other Parts

There are two screws at the bottom of the bulb socket, which is where the lamp cord is connected to the remainder of the lamp body.

When you lose the screw and replace the bulb then you can change the cord into the lamp.

You’ll do this by taping one end of that chord to the old chord. Pull the old cord from the highest of the lamp. In doing so, you will be pulling within the new chord.

Make sure that there is enough of the new chord beginning of rock bottom to succeed in electrical outlets.

If you do not plan on having the lamp far away from an outlet, 5 to six feet will do. If you propose having it further faraway from an outlet, try extending 8 to 9 feet of chord out of the lamp.

Once you’ve got your preferred length, cut the highest of the chord with wire cutters.

Prepping and Connecting the Wires

At the top of the new chord, remove a number of the insulation. it is the rubbery material around the wires.

Try removing around 2 to three inches of the insulation with wire strippers. After that’s done, grab a replacement electrical plug and loosen the 2 screws thereon.

Then, take the uncovered wire and wrap it around the two screws. Once that’s done, put the duvet back over the electrical plug.

On the opposite end, take the bare end of the lamp cord, and put them at the bulb end of the sunshine socket where there are two screws.

Take one wire and put one to every, then wrap them around each screw until they’re tightly secured.

Putting It Back Together

Pull the chord from the rock bottom end to urge obviate any slack. Once that’s done, attach the bulb socket back to the lamp with the nut.

When screwing it back on, turn the nut clockwise. Once that’s back on the lamp, be happy to place the lampshade back on, and plug it into the wall to check if the chord is on correctly.

If the lamp doesn’t activate, countercheck that the wires are tight onto the screws found on the plug and on the bulb socket.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button