Floor lamps are the best things for bringing soft light into your room or in your office, but it is often frustrating when your floor lamp switch stops working. Rather than throwing your floor lamp away, try installing a replacement light switch by yourself!
It’s a simple project that even a beginner can tackle, and you’ll replace the switch whether it’s located on the floor lamp itself or the cord. All you would like are a couple of simple tools, and you’ll be out of the dark in no time!
Replacing a Socket Switch
Remove the plug:
Don’t try to become a superhero. Make sure that you have already removed the plug from the socket when you start your work.
In the next step, you should try to remove the socket on top of the floor lamp. On most lamps, this is the place where the switch is based.
Squeeze and pull the socket shell to get rid of it from the floor lamp. The socket shell is that the actual assembly where the switch is found, and therefore the light bulb screws in. On most lamps, you’ll squeeze the socket shell and pull upwards to get rid of it.
If it is difficult to get rid of the socket shell, then you should use the screwdriver to loosen it.
Locate the wires attached to the socket shell. Two wires should be connected with the switch. One is hot, and therefore the other is neutral. The recent wire is typically attached to a brass screw, and consequently, the neutral wire is generally connected to a silver screw.
The neutral wire is typically marked in how. it’s going to be a particular color, or the insulation could also be printed, stamped, or have indentations. Confirm to notice this now, since you’ll get to know which wire is neutral once you attach your new switch.
If you can’t identify the neutral wire, check out the plug. The neutral wire is attached to the broader plug blade on a polarized plug. If your plug blades are an equivalent size, you ought to replace the plug while you’re replacing the socket.
Use wire cutters to chop the wires resulting in the prevailing switch. Traverse the wires as on the brink of the switch as possible to make sure you’ve got many wires to figure with.
Cut off the ends of the wire and strip away 1.3 cm of covering. Wire cutters also can be wont to strip insulation from wires. Use the wire cutters to form a notch within the wires’ insulation, then crackdown on the insulation with the strippers and punctiliously pull the insulation away.
If you see any strands of wire once you shy away from the insulation, it means you narrow too deep. Stop that section and begin again.
String the two wires through your socket and fasten them to the screws. Use your fingers to wrap the wire tightly around the screw. Make certain to attach the neutral wire to the silver screw and, therefore, the hot wire to the brass screw.
Although sockets will be slightly different counting on the manufacturer, the wires should thread easily through the socket. Confirm the socket is right-side-up and appearance for wire channels to help you recognize where to guide the wire.
Place the new socket shell into the lamp and depress. You ought to hear the new socket shell snap into place. If there’s a screw on the lamp’s stem, tighten it now to carry the socket in situ.
Replace the sunshine bulb and lampshade and connect the lamp. If you’ve done everything right, you ought to be ready to use your new switch to show on your lamp!
If the lamp doesn’t come on, check the connection in your switch and check out again. If this does not help, you’ll get to replace the plug.
Replacing a Cord Switch
Look for printing on the lamp cord to work out the dimensions switch you would like. Search for printing that says either SPT-1 or SPT-2. The printing is small, so you would possibly need to look carefully.
The difference between SPT-1 and SPT-2 affects the density of the lamp cord.
Examine your new switch to ascertain which wires you’ve got to chop. Some switches only require you to attach the recent wire. If this is often the case, there’ll be a channel along one side of the switch for the neutral wire.
Remove the prevailing cord switch. you’ll be ready to open the casing of the general switch and take away the wires without cutting them, but if not, use wire cutters to chop as on the brink of the switch as you’ll.
Try to avoid cutting the neutral wire. If you’ve got to chop it to get rid of the old switch, strip the insulation and connect the neutral wire’s cut ends together. If you wish, add a plastic connector to guard the wire in the situation you would like your new switch.
If you’re adding a cord switch when there wasn’t one before, use a little knife to carefully split the cord where you would like your new switch to travel, then traverse the recent wire. If your switch requires you to connect the neutral wire, cross that too.
Layer about 1.3 cm of covering off of the wires. Use your wire cutters to form a notch within the wire insulation, then gently pull to get rid of it. Only begin the maximum amount of insulation as you would like to connect the wires to the screws within the switch.
Match the recent and neutral wires to suitable screws. If you have one screw, it’s for the current wire. If you’ve got to attach both the recent and neutral wires, the recent wire goes to the brass screw, and therefore the neutral wire goes to the silver screw.
Insert the stripped wires into the screw terminals. Use your fingers to wrap the wires around the screws securely, and confirm there’s enough insulation on the wires so that no live wires are going to be exposed once you close the switch.
Make sure there is no visible wire showing when you assemble the switch. All you ought to see is an insulated cord.
If the exposed wires are too long, use the wire cutters to snip a little portion and reattach them to the screws.
Close the duvet on the switch and snap or screw it shut. Confirm that the duvet closes securely, and there are not any bare wires showing around the switch.
Plug-in your floor lamp and check out your new switch. If you’re confident that the switch seems like it’s securely connected and there are not any live wires showing, it’s time to check out your lamp! If you hooked everything upright, you ought to be ready to connect the floor lamp and switch it right.
If the floor lamp doesn’t activate, double-check your wiring and check out again.